02 · YOUR DRAFTING COMPANIONThe shape of things
ALL RADII START AT THE SAME CENTRE
Your measurements, made visible.
Select Calculate to see your shape and radii.
Scaled geometry · illustration only, not a cutting patternSeam / finished lineCut line
- AWaist seam radius
- BWaist cut radius
- CFinished hem radius
- DHem cut radius
- Hem circumference
- Finished waist opening
One unbroken full circle: width check
A diameter-only check for a single flat full circle. For panel layouts and estimated fabric length, use the panel layout block below.
Exclude selvages. No cutting margin is added.Calculate a full-circle example to check its width.
Cut in panels · fabric length
Panels are turned end-for-end (180°) and interleaved to save fabric. Side-seam allowance is reserved across the fabric width; the diagram shows the panel without it. Waistband fabric is separate.
- Panel · annular sector
- Grainline · parallel to selvedge
- Selvedge
Calculate to estimate a panel layout and fabric length.
Printable paper pattern · 1:1
Prints one full-size panel template to cut N times. In your browser print dialog choose "Save as PDF" and set scale to 100% / "Actual size". Measure the 5 cm and 2 in squares on the first page before printing the rest.
Examples
Select an example to calculate. Fabric amounts are rough guides; use the current panel layout estimate to plan your cut.
A LITTLE GUIDANCE, BEFORE YOU CUT
From numbers to paper.
01 / FIND YOUR CENTREStart with the angle.
Mark a centre on flat paper. Your shape uses 360°, 270°, 180° or 90°. Measure every radius from that same centre, including the empty space at the waist.
02 / FOLLOW THE LINESKnow where to cut.
A is the waist seam; B moves inward by your waist allowance. C is the finished hem; D moves outward by the total hem turn-in. Allowances are already included in B and D.
03 / MAKE A TESTPlan the finishing.
Add seam allowances wherever you divide the shape into panels. Plan a waistband and opening separately. Test on paper or scrap fabric before cutting your final fabric.
Circle skirt math
The waist seam follows part of a circle. Its radius = waist ÷ (2π × fraction). Use the finished waist opening: body waist plus wearing ease for a zipper, or the wider pull-on opening for elastic.
The fraction is 1 for a full circle, 0.75 for a three-quarter circle, 0.5 for a half circle, and 0.25 for a quarter circle.
A half circle uses only half the circumference. For the same waist, its radius must be twice the full-circle radius to make that shorter arc reach all the way around your body. Waist allowance moves the cutting line inward; skirt length extends outward from the waist seam.
How to hem a circle skirt
Parts of a circle skirt lie on the bias, diagonally across the fabric grain. These areas stretch more than the straight grain, so the hem can drop unevenly.
Hang the skirt for at least 24 hours before hemming. Then try it on with the waistband at its intended height and have someone mark an even hem by measuring up from the floor.
Trim to the level line, leaving your hem allowance. Use a narrow double turn, pressing and stitching small sections at a time, or finish with a bias facing for a smooth curved edge.
Zipper or elastic?
A zipper gives a fitted waist without needing stretch in the fabric. Opening the zipper gives you room to put the skirt on; close it for a neat waist fit.
Elastic offers pull-on comfort. The fabric opening must pass over your hips, and the elastic must stretch enough to do the same before returning to your waist.
Enter your hip measurement and read the calculator’s hip check in the elastic note. It checks an assumed 50% elastic stretch; test your actual elastic before cutting, because different types stretch differently.
A drafting aid, with clear limits. The diagram shows geometry, not instructions to cut on folded fabric. The width check covers one unbroken full circle only. Use “Cut in panels · fabric length” for a nested panel layout and fabric length estimate. Account for shrinkage, print direction and bias drop in your own construction plan.